I haven't been able to record for almost 2 years. The sample rates are the same for the session and imported files, so it seems unusual that this occurs. I have noticed a further problem where imported audio into PT10 plays slower and has a longer track time than it should. I am beginning to feel the fault is with the Mbox 2, as the issue occurs even when Pro Tools is uninstalled and I'm just using guitar sims on their own. Windows System : Microsoft Windows 7 Home (Service Pack 1) Wireless Adapter : Qualcomm Atheros AR9285 802.11b/g/n WiFi Adapterīattery No 1 : Hewlett-Packard Primary 51.15Wh/4.14Ah Network Adapter : Realtek PCIe GBE Family Controller (Ethernet) Media Player : RIM BlackBerry SD (1.84GB) Printer : Microsoft XPS Document Writer (600圆00, Colour) USB Controller 2 : HP P55/PM55/3400 USB2 Enhanced Host Controller USB Controller 1 : HP P55/PM55/3400 USB2 Enhanced Host Controller LPC Hub Controller 1 : HP HM55 LPC Interface ControllerĪudio Device : HP P55/PM55/3400 High Definition AudioĪudio Device : HP Redwood HDMI Audio ĭisk Controller : HP P55/PM55/3400 4 port SATA AHCI Controller STALKER (F:) : 3GB (UDF) hp CDDVDW TS-L633N (3.5GB, SATA150, DVD+-RW, CD-RW, 2MB Cache) Removable Drive (G:) : 2GB (FAT) RIM BlackBerry SD (2GB, USB2) Tracking down their causes can be far from easy but our step-by-step troubleshooting guide is here to help. Hp CDDVDW TS-L633N (3.5GB, SATA150, DVD+-RW, CD-RW, 2MB Cache) : 3GB (F:) Cicks and pops can ruin a recording, not to mention causing vast amounts of annoyance and wasted time. Video Adapter : ATI Mobility Radeon HD 5650 (400 SM5.0 550MHz, 1GB DDR3 1.6GHz 128-bit, PCIe 2.00 x16)Ĭompute Shader Processor : ATI Mobility Radeon HD 5650 (400SP 550MHz, 1GB DDR3 1.6GHz 128-bit) Monitor/Panel : AU Optronics Generic PnP Monitor (1600x1200, B173RW01 V3 Memory Controller : HP Core Mobile (Clarksfield) UnCore 2x 2.13GHz (4.26GHz), 2x 4GB DDR3 SO-DIMM 1.33GHz 128-bit Memory Controller : HP Core (Clarksfield/Lynnfield) DMI 2x 2.4GHz (4.79GHz) Model : HP Pavilion dv7 Notebook PC 103C_5335KV DPC Latency Checker says everything should work fine. I have been through the thread "READ THIS Before Posting!" thread and have followed the instructions (turning off fan control, turning off USB power management, etc). I have been using Pro Tools since PT7 was out so I understand the inner workings of it, and have had no problems until upgrading to this new laptop with PT9 and now PT10. It occurs not just in Pro Tools but also through stand alone programs such as various guitar amp sims (Amplitube 4 for instance). I am still getting the same pops and clicks. On the suggestion of users in the above thread I replaced my HDD in the laptop (32mb cache, 7200rpm with a hybrid 4GB SSD section). The previous issue is noted in this thread: I have had a previous issue which was unresolved and has left me without the use of my recording setup for almost 2 years. I made sure to go to the website and re-download the software and install it normally, rather than trying to use a backup.Hello. It’s perplexing because everything worked up until I re-installed Windows 10 a few months ago. Setting the amp’s processor priority to “High” doesn’t help.Issue occurs on any buffer size (greatest, lowest, or anything inbetween), and happens across 48khz-192khz, so basically occurs regardless of whatever setting used.DPC Latency reports that my latency isn’t an issue.Also uninstalled and reinstalled all relevant drivers (USB and Focusrite Control software) multiple times. I’ve tested it in all USB ports and the issue persists regardless. My interface is a Scarlett Solo 3rd Gen.My PC is an i9-9900k and 16GB DDR4 RAM, so my hardware should be more than sufficient.Issue doesn’t occur if using the amps as VST plugins through FL Studio 20. Issue occurs on the stand-alone software for Plini, Nolly, Omega, NTS, Abasi, and Cali.Here is a list of various relevant details…
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |